Jenn-Air JF36NXFXDE Manuel d'installation télécharger pdf (Page 18)

Move the Refrigerator into House

1. Place an appliance dolly under the left side of the refrigerator

as shown. Place the corner posts from the packing materials

over the trims as appropriate. Slowly tighten the strap.

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and

then lower the right-hand side of the refrigerator to the floor.

Install Anti-Tip Boards

IMPORTANT:

■ If a solid soffit is not available, anti-tip boards must be

installed.

■ It is recommended that boards be installed before the

refrigerator is installed.

■ Boards must be long enough to fully cover the width of the

compressor cover.

■ Place the boards so that the bottom surfaces of the boards

are 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up until the top of the

refrigerator is making contact with the bottom of the anti-tip

boards. Do not crush the compressor cover when raising the

rear leveling legs.

NOTE: The foam gasket, on top of the compressor cover, will

compress to fit under the anti-tip board(s). There is no need to

trim the gasket.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall.

2. Securely attach two 2" x 4" x 32" (5 cm x 10 cm x 81 cm)

boards to wall studs behind refrigerator. Use six #8 x 3"

(7.6 cm) (or longer) wood screws. The wood screws must be

screwed into the studs at least 1½" (3.8 cm). The boards must

overlap the compressor cover.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

Parts Needed

■ Minimum 7 ft (2.13 m) flexible, codes-approved water

supply line

Style 1—Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see

“Style 2—Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply.

IMPORTANT:

■ There is not enough clearance to achieve a flush installation if

a water shutoff valve is located in the wall behind the

refrigerator. The water shutoff should be located in the base

cabinet on either side of the refrigerator.

■ Before attaching the tubing to shutoff valve, flush the main

water supply line to remove particles and air in the water line.

Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

A. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

B. Attach to studs with six #8 x 3" (7.6 cm) screws.

C. Compressor cover

D. Distance from bottom of anti-tip boards to floor

2" (5 cm)

84"

(213.4 cm)

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 83 84

Commentaires sur ces manuels

Pas de commentaire

Jenn-Air JF36NXFXDE Manuel d'installation Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Réfrigérateurs Jenn-Air JF36NXFXDE