Jenn-Air JF36NXFXDE Manuel d'installation télécharger pdf (Page 10)

Water Supply Requirements

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ There is not enough clearance to achieve a flush installation if

a water shutoff valve is located in the wall behind the

refrigerator.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. The water supply line, however, must come up through

the floor in the gray shaded area shown.

■ A ½" (12.7 mm) hole for plumbing should be drilled on the

floor at least 6" (15.2 cm) from the right- or left-hand side

cabinet and should be no more than 1" (2.54 cm) away from

the back wall. See “Connect the Water Supply.”

■ The water supply connection is made at the front of the

refrigerator.

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and also clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Product Dimensions

IMPORTANT:

■ The depth from the front face of the doors to the back of the

refrigerator cabinet is 24" (60.96 cm) without panels.

■ The power cord is 84" (213 cm) long.

■ The water supply connection is made at the bottom front of

the refrigerator.

36" Single Door and 36" French Door Bottom Mount

Top View

Front View

■ Width dimensions were measured from hinge edge to clip

edge.

■ When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₄" (3.2 cm) to the height dimension.

(2.54 cm)

(15.2 cm)

35³⁄₄"

(90.8 cm)

24"

(61.0 cm)

83¹⁄₈"

(211.1 cm)

35³⁄₄"

(90.8 cm)

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 83 84

Commentaires sur ces manuels

Pas de commentaire

Jenn-Air JF36NXFXDE Manuel d'installation Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Réfrigérateurs Jenn-Air JF36NXFXDE